Re: [squid-users] WCCP Configuration

--- Awie <awie@eksadata.com> wrote:
> > /sbin/modprobe ip_wccp
> > echo 1 > /proc/sys/net/ipv4/ip_forward
> > /sbin/iptables -t nat -A PREROUTING -i eth0 -p tcp
> > --dport 80 -j REDIRECT --to-port 3128
> >
> > First line is load ip_wccp after every reboot
> > Second will enable ip forwarding
>
> Does it be needed to enable ip forwarding if I only
> have 1 N

this command is needed when you are using Virtual
interface like for GRE tunnel

i think here it is not needed

> Thx & Rgds,
>
> Awie
>
> > Third line will enable iptables
> >
> > Thanks and Regards
> >
> >
> >
> > --- Adeel Asher <adeel@worldcall.net.pk> wrote:
> > > Dear Mahmood Ahmed
> > >
> > > Here is the Linux configuration:
> > >
> > > Patching Kernel with WCCP v1 Support
> > >
> > > The following steps are needed:
> > >
> > > 1.Download the ip_wccp.c from
> > >
> >
>
http://www.squid-cache.org/WCCP-support/Linux/ip_wccp.c
> > > .Compile ip_wccp.c
> > > using the following command:
> > >
> > > gcc -D__KERNEL__
> -I/usr/src/linux-2.4.18-3/include
> > > -Wall -Wstrict-prototypes
> > > \
> > > -O2 -fomit-frame-pointer -fno-strict-aliasing
> -pipe
> > > -fno-strength-reduce \
> > > -m386 -DCPU=386 -DMODULE -DMODVERSIONS -include
> \
> > >
> /usr/src/linux-2.4.18-3/include/linux/modversions.h
> > > -c ip_wccp.c
> > >
> > > After this, the compiled ip_wccp.o will be
> created.
> > >
> > > 2.Copy ip_wccp.o to
> > > /lib/modules/2.4.18-3/kernel/net/ipv4/ip_wccp.o.
> > >
> > > Linux@Box#cp ip_wccp.o
> > > /lib/modules/2.4.18-3/kernel/net/ipv4/ip_wccp.o.
> > >
> > > Then edit /lib/modules/2.4.18-3/modules.dep
> > > Add the line:
> > > /lib/modules/2.4.18-3/kernel/net/ipv4/ip_wccp.o:
> > >
> > > 3. Test the module with:
> > > /sbin/modprobe ip_wccp
> > > /sbin/depmod -a -e
> > > This should report no errors.
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > > -----Original Message-----
> > > From: Mahmood Ahmed
> > > [mailto:braveheart@buraak.net.pk]
> > > Sent: Thursday, February 26, 2004 2:42 AM
> > > To: adeel@worldcall.net.pk
> > > Cc: squid-users@squid-cache.org
> > > Subject: RE: [squid-users] WCCP Configuration
> > >
> > > Hello Adeel
> > >
> > > can you please also explain the step by step
> (like
> > > you did below) wccp
> > > configuration for OS (Redhat 9.0) and Squid too.
> > >
> > > Regards
> > >
> > > Mahmood Ahmed
> > > Buraak Telecommunications Pvt. Ltd.
> > >
> >
>
---------------------------------------------------------
> > >
> > > This mail has been sent using Buraak Net's
> Mailing
> > > System
> > > (http://www.buraak.net.pk)
> > >
> > > ---------- Original Message -----------
> > > From: "Adeel Asher" <adeel@worldcall.net.pk>
> > > To: "'squid'" <squid-users@squid-cache.org>
> > > Sent: Wed, 25 Feb 2004 10:34:45 +0500
> > > Subject: RE: [squid-users] WCCP Configuration
> > >
> > > > Here You Go
> > > >
> > > > Router #
> > > > Router (config)# ip wccp version 1
> > > > Router (config)# ip wccp web-cache
> redirect-list
> > > 125
> > > > Router (config)# ip wccp web-cache redirect
> out
> > > > Router (config)# ip wccp redirect exclude in
> > > > Router (config)# ip wccp web-cache redirect
> out
> > > >
> > > > Access-List 125
> > > >
> > > > permit ip 192.168.92.0 0.0.0.255 any
> > > > permit ip 192.168.93.0 0.0.0.255 any
> > > > permit ip 192.168.94.0 0.0.0.255 any
> > > > permit ip 192.168.95.0 0.0.0.255 any
> > > > permit ip 192.168.96.0 0.0.0.255 any
> > > > permit ip 192.168.97.0 0.0.0.255 any
> > > > permit ip 192.168.98.0 0.0.0.255 any
> > > >
> > > > All permitted hosts in this access list will
> be
> > > redirected to squid for
> > > web
> > > > traffic.
> > > >
> > > > Router #Conf t
> > > > Router (config)#
> > > > Router (config)# interface fastethernet 0
> > > > Router(config-if)# ip wccp web-cache redirect
> out
> > > >
> > > > Router # Conf t
> > > > Router(config)#
> > > > Router(config)# Interface serial 0
> > > > Router(config-if)# ip wccp redirect exclude in
>
> > > > Router(config-if)# ip wccp web-cache redirect
> out
> > > >
> > > > I am assuming that your router serial is
> connected
> > > to WAN and FastEthernet
> > >
> > > > to LAN. If you have more than one serials you
> will
> > > have to enable it on
> > > all.
> > > >
> > > > Regards,
> > > > Adeel Asher
> > > > WorldCALL Multimedia
> > > > Lahore
> > > > PK
> > > >
> > > > -----Original Message-----
> > > > >From: Danish Khan
> [mailto:danish.khan@go4b.net]
> > > >
> > > > >Sent: Wednesday, February 25, 2004 4:31 AM
> > > > >T0: 'squid'
> > > > >Subject: [squid-users] WCCP Configuration
> > > >
> > > > >Can any body please explain the router
> > > configuration for WCCP.
> > > >
> > > > >Danish Khan
> > > ------- End of Original Message -------
> > >
> > >
> >
> > > ATTACHMENT part 2 application/pdf name=SQUID.pdf
> >
> >
> >
> > __________________________________
> > Do you Yahoo!?
> > Get better spam protection with Yahoo! Mail.
> > http://antispam.yahoo.com/tools
> >

__________________________________
Do you Yahoo!?
Get better spam protection with Yahoo! Mail.
http://antispam.yahoo.com/tools
Received on Thu Feb 26 2004 - 06:57:58 MST